3D打印

Prusa i3 配置文件

# generated by Slic3r 1.2.9 on Thu Feb 23 21:19:47 2017 avoid_crossing_perimeters = 0 bed_shape = 0x0,200x0,200x200,0x200 bed_temperature = 0 before_layer_gcode = bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 1 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84  ; disable motors\nM190 S0; turn off bed temperature external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 80% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 0.9 extrusion_width = 0 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #C51BD6 filament_diameter = 1.75 fill_angle = 45 fill_density = 80% fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_bed_temperature = 0 first_layer_extrusion_width = 0 first_layer_height = 0.4 first_layer_speed = 50% first_layer_temperature = 205 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 2 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 40% infill_speed = 80 interface_shells = 0 layer_gcode = layer_height = 0.2 max_fan_speed = 80 max_print_speed = 80 max_volumetric_speed = 0 min_fan_speed = 40 min_print_speed = 5 min_skirt_length = 0 notes = nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 40 perimeters = 3 post_process = pressure_advance = 0 raft_layers = 0 resolution = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 10 retract_lift = 0.3 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 seam_position = nearest skirt_distance = 2 skirt_height = 1 skirts = 2 slowdown_below_layer_time = 30 small_perimeter_speed = 35 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 60 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\nM107; turn off fan support_material = 1 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 10 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 45 temperature = 205 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 50 top_solid_layers = 3 travel_speed = 160 use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 xy_size_compensation = 0 z_offset = 1.6